How to Add Textures to an Appearance in SOLIDWORKS Visualize 2023 and Earlier

Problem

Adding appearances to a model in Visualize is the first step in any project, big or small. You can enhance appearances even more by adding textures. They will help improve the realism of appearances and make your models that much more photorealistic. In this article, we’ll discuss the process of adding textures to appearances for SOLIDWORKS Visualize 2023 and earlier. For SOLIDWORKS Visualize 2024 and newer, review this article:

How to Add Textures to an Appearance in SOLIDWORKS Visualize 2024 and Newer

Solution

You can add textures to your appearances by selecting the appearance in your Palette and navigating to the “Textures” section. Depending on the appearance type chosen, you can have up to four different texture mappings available in the "Texture" section: color, specular, alpha, and bump.

Texture_Property_Manager.png

From here, double-click on the map type and browse for the correct map file. Map files are generally image files (.jpg, .png, etc), and only one image file may be loaded into each map type at a time.

We can see a quick demonstration of the difference texturing can make down below.

Color Mapping

Color mapping does exactly what its name suggests: it allows you to add a color or an image to your appearance. This color or image will be applied everywhere that the appearance is applied, so if your appearance is placed on the entirety of a model, you’ll see the color map propagated to all faces of the model (as opposed to a decal, which is applied on a face-by-face basis).

Color_Texture.png

Above, we can see that the color map applied to the appearance has been applied not only to the spline surface but also to the bottom face of the model. This is because this particular appearance has been applied to the model as a whole, and so the color map is applied to all faces.

Specular Maps

Specular maps control the “glossiness” of a model’s appearance. Here’s an example of a specular map:

Cast Specular

While it looks like a mess of whites, blacks, and greys, when read as a specular map, each of those colors represents a certain amount of brightness that will be applied to a model’s appearance. Observe the model without a specular map (left) and with a specular map (right):

Black Appearance Black Spec

You can see how, as soon as the specular map shown above was applied to the sphere, the model was covered in darker and lighter areas of light. These speckles coincide with the darker and lighter colors in the specular map itself, and, when combined with a bump map, can simulate realistic lighting across a textured surface.

Alpha Maps

An alpha map controls the transparency of a model’s appearance. It essentially reads a greyscale image in order to know where to apply transparency to a model and with what strength. If you were to open an alpha image file by itself, you’d see that an alpha map looks very similar to a specular map: an image of whites, grays, and blacks.

We can see the effects of an alpha map by loading the above specular map from above as an alpha map:

Black_Appearance.png Cast_Alpha_.png

If we observe the picture on the right, we can still vaguely make out a spherical shape, but we can see that almost all of the sphere has been rendered transparent.

On a practical level, this type of alpha map is completely useless, but it does demonstrate exactly what an alpha map does.

Bump Maps

Bump maps simulate actual texturing across the surface of a model. Bump maps are responsible for most of the photorealism you’ll see in your model and will more accurately simulate what a material will look like as you apply it to your model.

A bump map is another image file that looks something like these:

carbon normal Cast Normal

Again, each color in a bump map is translated into the software to simulate a realistic, textured look on the surface.

Let’s take a look at a non-textured sphere and a sphere with a bump map applied to it:

Black Appearance Black Bump

We can see that as the bump map is applied, the surface of the sphere takes on the appearance of an actual material, rather than a smooth sphere.

Finding Additional Texture

By default, texture files are located in C:\Users\[USERNAME]\Documents\SOLIDWORKS Visualize Content, but you can change this directory at any time by going to Tools -> Options -> General.

Cloud Library

You can also find more textures by clicking on the “File Libraries” tab in your palette, clicking on the “Cloud” option, and changing the category to “Textures”:

Texture Library

After that, you can simply double-click and download any textures that you would like to use. Since textures are just image files, you can download any image file you’d like to use as a texture.

For additional support, existing customers can submit a ticket or new customers can contact Hawk Ridge Systems. 

Was this article helpful?
0 out of 0 found this helpful

Articles in this section

Comments

0 comments

Article is closed for comments.